1:10th Scale Accessories

While taking pictures of a local landrover owners vehicle, I noticed he had steps fitted, and thought 'Hey' I like those so set about making a set. While they are only small I tried to get as much detail into them as I could including the spiky grip tread bits, so they looked like the real thing. These...

This is a 1:10 th scale fuel cell based on pictures I found online, and while it doesn't do anything, it can just finish a scale truck of car off perfectly. Dimensions: 55mm Deep. 72mm Wide. 20mm high. This comes complete with a bit of imitation braided fuel hose, and...

This is scale 7kg gas cylinder which is ideal for a roof rack or trailer accessory, and comes complete with new high resolutionn 3d printed valve and white on clear waterslide decals for either butane or propane pending what colour you want to paint it. I have also included pictures of one I painted...

This was one of those after thoughts I had after I made my new sports seat and that was to fit those to a gelande interior was a lot of work, so decided to make a replacement back only as the old seat back just slots into place, so tweaked my design a bit and built a jig for drilling mounting holes and...

This is a replacement front bumper for the D90 styrene body and a direct reproduction of the real steel standard bumper that land rovers have right down to the fully shaped end caps with detail on the top. It comprises of a cut to length piece of styrene tube, a pair of end caps and fixing brackets....

This is my new injection moulded front grill replacement for the Gelande Landrover D90 and D110 body that's widely available. This is now a tweaked version of the previous new grill as its now made in black nylon composite, plus I have added lugs to the main grill which allow it to be push fitted to...

This is something I spotted on a land rover locally an over rider bar as it is called, so being quite a simple apart set about making one as a cosmetic addition. Its injection moulded out of HIPS so can be stuck to the front bumper I make using polystyrene cement model glue and is something you can drape...

This is one of those parts that I thought just finishes off a scale land rover, a fuel filler cap. I noticed on earlier models, especially the D90 that it had the fuel filler cap between the door and rear wheel arch, plus it was rectangular instead of oval at the top so set about making. For this to...

This is my new injection moulded fuel recess and one of those parts that I think just finishes off a scale land rover. I had quite a lot of feedback from my resin version so applied that input to the new version. Firstly some people found it tricky to cut out a perfect hole in the rear, so the new version...

This is just another one of those detail pieces for people that want to turn the later body into an earlier one, that being the recessed side door handles. This is my new injection moulded version which is the same as the old resin one, just in HIPS which sticks much better to the body. Each handle comes...

With so many trucks around I thought I would do a range of wing vent covers bases as closely as I could get on the real versions, just to give people a choice when it comes to dressing their truck. This version comes with struts running the length way and a mesh grill behind, which I noticed some of...

I noticed when it came to wing vent covers the only choice was the ones that came with the D90 body, so after looking through some pictures decided to make a couple of different versions. This was made to look like the top grills that have the four smaller vent slots in, the back being the highest...

With so many trucks around I thought I would do a range of wing vent covers bases as closely as I could get on the real versions, just to give people a choice when it comes to dressing their truck. This version comes with a square mesh pattern as well as tiny bumps to imitate fixing bolts round the lip...

This is a conversion kit for the gelande landrover, to turn the stock bonnet into the later one with the bulge. The kit comes with a cnc cut piece to flat off the old bonnet and vac formed bulge and support piece to go underneath just to hold the flat plate in place. It does require a fair bit of work...

This is a replacement front bumper for the D90 styrene body and unlike the other one I make which is a more traditional version, this is a more modern version that incorporates a place for a winch. It was based on pictures I found on the internet but I tweaked the design so that the commonly used 3 racing...

This is a replacement rear bumper for the D90 styrene body. So I bought a landrover d90 body and found while the bumper that came with it was ok, it was a bit flexi and lacked some detail, so set about making a more detailed version from a local guys real one. It comes with a pair of die cut rubber mud...

This is a replacement rear bumper for the D90 styrene body, which I made to match the type 2 front bumper I make. Its not really based on anything, I just incorporated the design of the front one into one for the rear and included matching end sections and large step which has checker plate just to finish...

This is the first of my new injection moulded parts, the rear door handle. Its made from white HIPS which has several benefits over resin, the main being it sticks much better to the body as they are both made of it. I have included a picture of one sprayed red so you can see the detail better, as it...

This is the first of my new injection moulded rear wheel carriers. The design has been tweaked so it now fits with the rear door handle in place, and comes in pieces so the frame and mounting brackets are separate meaning if you want it to be able to swing open it can, or just be glued closed. Of course...

This is the second of my new injection moulded rear wheel carriers and like the first the design has been tweaked so it now fits with the rear door handle in place and comes in pieces so the frame and mounting brackets are separate meaning if you want it to be able to swing open it can, or just be glued...

This is the third of my new injection moulded rear wheel carriers, but unlike the other two this offsets the spare wheel to the right side as I am also working on a jerry can bracket and frame which will mount on the left. Like the other two the frame and mounting brackets are separate meaning if you...

This is my new Type 1 snorkel, and as the old mold had worn out it was ready for injection molding, so decided not to just redo the old version, but went with the latest version that I saw on the special edition land rovers, which looked a bit sleeker. It now comes with pre threaded holes in the back...

This is my new version type 2 snorkel which now has more realistic detail thanks to injection moulding and fits on top of the wing just like the old one instead of the side, and has an air filter mounted at roof level. I have also tweaked the wing mounting plate which now screws into place and also fits...

These are my new Snow cowls as they are normally referred to which have been redesigned from the ground up so now they fit the Gelande, Team Raffee and other vac formed bodies. They are a slightly new shape with much more finer detail than before and now come in two parts which allows them to fit all...

This is my new sports seat which I made for my new Team Raffee defender build. It will also fit the gelande, but you will need to cut away the old seat base, hence I have also made a gelande direct replacement back only, (listed separately) plus this seat will fit any other 1:10 scale rc car or truck...

These are my wheel arches which I made to fit my Team Raffee body, as I wanted something a bit more beefy than the ones that came with it, and also both slightly wider and deeper to clear larger diameter tires. They also fit the older gelande style body as well, but the old wheel arches will need removing...

This is my set of wheel arches made to fit the Gelande body, which are squarer and not quite so chunky as my other set, and while made for the gelande body they also fit the team raffee one as well. When fitting to the gelande body the old wheel arches do need cutting off first. For fixing them on, they...

These are my new luggage straps, which use the same scale injection moulded buckles as my Bed Roll. You get six buckles and two metres of strapping, so you can make straps to fit whatever you want, short or long. I have now put together a few pictures to show the easiest way to assemble them, as some...

These are my new luggage straps, which use the same scale injection moulded buckles as my Bed Roll. You get six buckles and two metres of strapping, so you can make straps to fit whatever you want, short or long. I have now put together a few pictures to show the easiest way to assemble them, as some...

This is was just one of those parts that came along as I needed to fill my roof rack up a bit, and as my truck is based on a long range explorer vehicle a spare drum or can of oil would be a must. Dimensions are 45mm high without handle, and 29mm diameter, so in real terms it's about a 7 gallon...

This was actually modelled off my own tool box, and thought it was quite a nice extra item to have on either a trailer or sitting in the back of your pick up on the flatbed. This item is hollow cast and open from the bottom, and comes in beige resin ready for you to paint.

This is just another version of tool box which I saw while at a classic car show, and while not that old, I liked the shape so set about making one. Not an essential item, but can just finish a truck off. This item is hollow cast and open from the bottom, and comes in beige resin ready for...

All my towing ropes and cables now come with a proper machine swaged ends, meaning they are stronger than ever. This is the first in my new range of towing cables and t his version uses stainless steel cable with a machine swaged thimble at each end and is 12 inches long and comes with yellow tubing...

All my towing ropes and cables now come with a proper machine swaged ends, meaning they are stronger than ever. This is a 10 inch length of 3mm scale nylon rope with a thimble swaged to each end, then to finish it off like the ones from the 4x4 accessory shop with yellow tube covering each end and a...

All my towing ropes and cables now come with a proper machine swaged ends, meaning they are stronger than ever. This is a 10 inch length of 3mm soft cotton twisted cord and while it can pull your truck out of a sticky situation I picked cotton for this version as unlike the nylon it drapes so much more...

All my towing ropes and cables now come with a proper machine swaged ends, meaning they are stronger than ever. This is a 10 inch length of 2mm nylon cord, but a bit more modern than the other two I sell and while it can pull your truck out of any sticky situation it also drapes nicely and holds its...

This is what they call a tree saver strap, which in real life is wrapped around a tree to pull your truck out of trouble, but unlike the steal cable on the winch it doesn't damage the tree, hence its name. It's made from heavy duty nylon strap and thermally welded together, and a few finishing touches...

This is what they call a tree saver strap, which in real life is wrapped around a tree to pull your truck out of trouble, but unlike the steal cable on the winch it doesn't damage the tree, hence its name. It's made from heavy duty nylon strap and thermally welded together, and a few finishing touches...

This is what they call a tree saver strap, which in real life is wrapped around a tree to pull your truck out of trouble, but unlike the steal cable on the winch it doesn't damage the tree, hence its name. It's made from heavy duty nylon strap and thermally welded together, and a few finishing touches...

This is a scale replica van or truck vault, and was actually modelled off a guy down the roads who kindly let me take some details of his. Dimensions 97mm Wide 57mm Deep (excluding handle) 25mm High This item is hollow cast and open from the bottom, and comes in beige resin ready...

This is my new version of the Clansman FFR Wing Box which is used to house the TUUAM and external Antenna and comes in three parts. This version has the box split more in the middle and while this means a bit of gluing and filling, it does allow for much better catch detail which some of which was lost...

I noticed a lot of WMIKS at shows had a older style of fire extinguisher mounted in them, so as it was quite easy made one, as it just looks better than the more modern ones you can get. You get one of these in resin ready for you to paint and attach to your Land Rover.

This is a replacement front bumper for the D90 styrene body and also one of my new parts for the WMIK version of the landrover and comes with more surface detail and a towing recess like the WMIK version has, but can also be used on a standard land rover too. While it doesn't fit directly to the body,...

This is one of those parts I just loved when I first saw it at a car show, and after speaking to the owner took a few pictures and dimensions like you do, and set about scaling it down. It came out better than I hoped when finished, and have included a pair as sometimes you see one each side, and others...

You get a pair of these and normally you would have a clansman box one side and an aerial the other, but sometimes one is left empty, but you tend to always see two fitted, hence two are included. You get a pair of these which come in resin and just needs you to paint and attach to your Land Rover.